• xd engine conversion

    XD Falcon Engine Conversion

    Wednesday, December 14, 2011

    A little project I have been working on lately is my XD Fairmont Ghia. The car was ‘handed down’ I suppose you would say after my grandfather passed away, well actually nobody else in the family wanted it! Anyway, the old 4.1 crossflow and 3-speed auto just wasn’t doing it for me so I got [...]

    Read More
  • ng-pajero-diagnosis-connector-1

    Pajero ECU Fault Code Check

    Friday, April 1, 2011

    In this article we are taking a look at how to extract ecu fault codes for the Mitsubishi Pajero V6. This information covers the NF, NG, NH and NJ models.   To extract the codes on the Pajero you will need either a analogue volt meter or LED test light. The volt meter or test light [...]

    Read More
  • ng-pajero-diagnosis-connector-1

    Pajero V6 Timing Check And Adjust

    Friday, April 1, 2011

    This article covers checking and adjusting the ignition timing on NF, NG, NH and NJ model Pajero’s fitted with the 3.0 V6 engine. Before checking or making any adjustments to the timing the Timing Check Connector must be earthed. A length of electrical wire with small alligator clips on each end is handy for this, [...]

    Read More
  • Falcon-Front-Brake-Pads-0131

    How To Replace Falcon Front Brake Pads

    Thursday, March 31, 2011

    Today we are looking at how to replace the front brake pads on a Ford Falcon. The vehicle that we are using for this article is a 1999 model AU, however if my memory serves me correctly the same front brake setup is used from the EA up to the last of AU’s, as well as [...]

    Read More
  • welsh-plug-replacement-002

    How To Replace Welch Plugs

    Tuesday, March 15, 2011

    In this article we are going to take a look at what is involved in replacing welch plugs, otherwise known as freeze plugs, expansion plugs or welsh plugs with an ‘s’. What we are doing with this article is covering only the actual removal and replacement of a welch plug itself on a scrap engine, [...]

    Read More
  • efi-timing-013

    EFI Ignition Timing Check And Adjust

    Tuesday, March 15, 2011

    Today we are looking at how to check and adjust the ignition timing on an engine equipped with efi (naturally this does not include distributor-less (coil pack) type ignitions). Engines that are controlled by an ecu require the computer to be put in a ‘diagnostic’ or similar mode before the ignition timing can be checked and adjusted.   [...]

    Read More
  • cruiser-012-1

    Chev Tuned Port Injection Conversion – The Finish

    Friday, March 11, 2011

    A quick update for those of you interested in the Tuned Port Injection conversion that we have been doing on a 350 fitted to an 80 series Landcruiser. After deciding that we wanted the ecu inside the car and up under the dash out of harms way we spent quite a bit of time extending the [...]

    Read More
  • 5S-FE-timing-belt-0151

    Toyota 5S-FE (2.2) Timing Belt – Part Two

    Thursday, March 10, 2011

    In Part One we got as far as having everything apart and ready to replace the oil seals and the oil pump gasket. I prefer to replace the oil pump gasket and then clean everything down before replacing the three oil seals. The reason for this is that there will be some oil spillage from the oil [...]

    Read More
  • 5S-FE-timing-belt

    Toyota 5S-FE (2.2) Timing Belt – Part One

    Tuesday, March 8, 2011

    Today we are going to take a look at what is involved in replacing the timing belt on a Toyota 5S-FE engine. This is the 2.2 litre engine commonly found in the wide-body Camry models. This article is going to be a long one, not because the job is a particularly difficult one but because [...]

    Read More
  • vt-commodore-waterpump

    VT Commodore Drivebelt Replacement – V6

    Friday, February 18, 2011

    Today we are looking at what is involved in replacing the drivebelt on a V6 VT Commodore. This is a nice easy job as long as you have either a 15mm spanner or 15mm socket and ratchet. The spring-loaded belt tensioner is a little tricky to get to as the top radiator hose can get [...]

    Read More

How To Paint A Car

dent repair
Feb
2

How To Repaint A Car – Part Four – Dent Repair 2

Posted by · 4 Comments

Our VN’s panels are in pretty good condition however they have not been immune to the usual shopping trolley dents and with the passengers rear door being the worst we thought we would start there. I find it easier to remove the panel from the vehicle if possible, having a damaged spine makes it almost [...]

Read More
ScreenHunter_01 Oct. 19 22.52
Jan
3

How To Respray A Car – Part Five – Applying Primer

Posted by · 7 Comments

Part Five, in what is steadily becoming the longest diy tutorial in history is all about applying the primer to the repaired panels. A quick note before we begin. Always check the local rules and regulations regarding the use of automotive paints. Often times it will be illegal to spray these paints at your home [...]

Read More

Cylinder Head